151-0544-00L  Metal Additive Manufacturing - Mechanical Integrity and Numerical Analysis

SemesterHerbstsemester 2022
DozierendeE. Hosseini
Periodizitätjährlich wiederkehrende Veranstaltung
LehrspracheEnglisch



Lehrveranstaltungen

NummerTitelUmfangDozierende
151-0544-00 GMetal Additive Manufacturing - Mechanical Integrity and Numerical Analysis3 Std.
Fr10:15-13:00CHN C 14 »
E. Hosseini

Katalogdaten

KurzbeschreibungAn introduction to Metal Additive Manufacturing (MAM) (e.g. different techniques, the metallurgy of common alloy-systems, existing challenges) will be given. The focus of the lecture will be on the employment of different simulation approaches to address MAM challenges and to enable exploiting the full advantage of MAM for the manufacture of structures with desired property and functionality.
LernzielThe main objectives of this lecture are:
- Acknowledging the possibilities and challenges for MAM (with a particular focus on mechanical integrity aspects),
- Understanding the importance of material science and metallurgical considerations in MAM,
- Appreciating the importance of thermal, fluid, mechanical and microstructural simulations for efficient use of MAM technology,
- Using different commercial analysis tools (COMSOL, ANSYS, ABAQUS) for simulation of the MAM process.
Inhalt- Introduction to MAM (concept, application examples, pros & cons),
- Powder-bed and powder-blown metal additive manufacturing,
- Thermo-fluid analysis of additive manufacturing,
- Continuum-based thermal modelling and experimental validation techniques,
- Residual stress and distortion simulation and verification methods,
- Microstructural simulation (basics, analytical, kinetic Monte Carlo, cellular automata, phase-field),
- Mechanical property prediction for MAM,
- Microstructure and mechanical response of MAM material (steels, Ti6Al4V, Inconel, Al alloys),
- Design for additive manufacturing
- Artificial intelligence for AM
Exercise sessions use COMSOL, ANSYS, ABAQUS packages for analysis of MAM process. Detailed video instructions will be provided to enable students to set up their own simulations. COMSOL, ANSYS and ABAQUS agreed to support the course by providing licenses for the course attendees and therefore the students can install the packages on their own systems.
SkriptHandouts of the presented slides.
LiteraturNo textbook is available for the course (unfortunately), since it is a dynamic and relatively new topic. In addition to the material presented in the course slides, suggestions/recommendations for additional literature/publications will be given (for each individual topic).
Voraussetzungen / BesonderesA basic knowledge of mechanical analysis, metallurgy, thermodynamics is recommended.
KompetenzenKompetenzen
Fachspezifische KompetenzenKonzepte und Theoriengeprüft
Verfahren und Technologiengeprüft
Methodenspezifische KompetenzenAnalytische Kompetenzengeprüft
Entscheidungsfindunggeprüft
Problemlösunggeprüft
Persönliche KompetenzenKreatives Denkengeprüft
Kritisches Denkengeprüft

Leistungskontrolle

Information zur Leistungskontrolle (gültig bis die Lerneinheit neu gelesen wird)
Leistungskontrolle als Semesterkurs
ECTS Kreditpunkte4 KP
PrüfendeE. Hosseini
FormSemesterendprüfung
PrüfungsspracheEnglisch
RepetitionEs wird ein Repetitionstermin in den ersten zwei Wochen des unmittelbar nachfolgenden Semesters angeboten.
Prüfungsmodusmündlich 20 Minuten
Zusatzinformation zum PrüfungsmodusIn addition to the final oral examination, there is one compulsory continuous performance assessment. Eight small simulation assignments will be presented starting from the 3rd week of the semester in exercise sessions. The students are expected to follow video-instructions for setting up a simulation case per assignment (in COMSOL or ABAQUS or ANSYS) and submit a single-page report covering the simulation results and their personal interpretation of the results. There will be 3 weeks time for submission of the solution (report) for each assignment and the lecturer will be available for discussion and support within this time period. The reports will be graded and the average of the six best assignment grades will count 30% towards the final course grade. Not handing in an assignment at all will result in a grade 1 The remaining 70% of the final grade will be based on a 20-min oral exam.

Lernmaterialien

Keine öffentlichen Lernmaterialien verfügbar.
Es werden nur die öffentlichen Lernmaterialien aufgeführt.

Gruppen

Keine Informationen zu Gruppen vorhanden.

Einschränkungen

Keine zusätzlichen Belegungseinschränkungen vorhanden.

Angeboten in

StudiengangBereichTyp
Doktorat MaterialwissenschaftAdvanced Manufacturing (MaP Doctoral School)WInformation
Doktorat MaterialwissenschaftStrength & Durability of Materials (MaP Doctoral School)WInformation
Maschineningenieurwissenschaften BachelorDesign, Mechanics and MaterialsWInformation
Maschineningenieurwissenschaften MasterMechanics, Materials, StructuresWInformation
Materialwissenschaft MasterWahlfächerWInformation